Primer and Rigging

Rig of the vehicle. The rig of the vehicle is performed when the aim is to isolate the piece and serve as a support to the paint finish. The painting of rigging applied with spray guns with peaks stage nozzle medium, and must always be put after the filler of polyester to fill imperfections and isolate it.

Once the paint rig is dried it is important to make a proper sanding of the rig to get a perfect finish for both the color as with his later varnished.

To make a rig in the correct way, the most advisable thing is to make use of a scale granolumetrica of the sandpaper. So that you do not sobrepe more than 100 numbers between scale of sandpaper. In addition there will also be using a belt sander broken orbital socket 3 with inhalation of dust from sanding. That will be the true key to the success of sanding.

Primer of the vehicle

In a primer of the vehicle, which seeks to protect the sheet metal from oxidation. In addition, in the case of metal substrates and on the plastic surfaces, what you want would be to promote adhesion of the phases of the painting.

Keep in mind that the paint for car you need a base to protect the metal surfaces from possible corrosive agents who would be the contact of the metal with humidity environment.

For this you have to see beforehand what type of primer is the correct one to each substrate and each phase of the repair. In this case, the most common would be putty.

Among the methods of priming the most common we find Primers fosfatantes curing acid that serve to give a protection of oxide to the metal. It is recommended for use when it is exposed to the metal before moving on to the phase of the prepared.

The Primers are two-component Epoxy, in turn, would be used to protect and seal the metal against corrosion.

-

PRIMER AND TACKLE FREQUENTLY ASKED QUESTIONS:

In this section you will find all kinds of primers and gear. Tested and 100% recommended. Products used as the first layer of surface treatment or piece to paint.

What is the primer to be used in vehicles?

The primer is a coating that is previously applied on the surface to be painted to make it optimally prepared to move to the subsequent process.

What do you look for to get the primer in a vehicle?

In a primer of the vehicle, which seeks to protect the sheet metal from oxidation. In addition, in the case of metal substrates and on the plastic surfaces, the aim is to promote adhesion of the phases of the painting.

What should we know before you perform a primer in a vehicle?

Keep in mind that the paint for car you need a base to protect the metal surfaces from possible corrosive agents who would be the contact of the metal with humidity environment.

For this you have to see beforehand what type of primer is the correct one to each substrate and each phase of the repair. In this case, the most common would be putty.

What are the methods of priming the most common?

Among the methods of priming the most common we find primers fosfatantes curing acid that serve to give a protection of oxide to the metal. It is recommended for use when it is exposed to the metal before moving on to the phase of the prepared.

The Primers are two-component Epoxy, in turn, would be used to protect and seal the metal against corrosion.

What is the rig?

In short, the rig cars will be the last layer to be applied before the paint finish.

¿When is the rig?

The rig of the vehicle is performed when the aim is to isolate the piece and serve as a support to the paint finish.

The painting of rig has a vital importance during the repair process, by directly influencing the productivity and profitability of the work, as well as in the quality of the final finish of the vehicle. The rig of the vehicle is performed when the aim is to isolate the piece and serve as a support to the paint finish.

How to apply paint to rig?

The painting of rigging applied with spray guns with peaks stage nozzle medium, and must always be put after the filler of polyester to fill imperfections and isolate it.

Once the paint rig is dried it is important to make a proper sanding of the rig to get a perfect finish for both the color as with his later varnished.

How do you make a rig correctly?

To make a rig in the correct way, the most advisable thing is to make use of a scale sizes of the sandpaper. In such a way that it does not exceed more than 100 numbers between scale of sandpaper. In addition, there will also be using a belt sander broken orbital socket 3 with inhalation of dust from sanding. That will be the true key to the success of sanding.

What is the purpose of the rig?

The purpose of the rig is to isolate the part to be treated and also serve as a support to the painting I just end.

What is it used for the rig?

We may use the rig as insulation and support, to improve the fit of the color of the paint end and to provide a regular basis on the treated surface.

There is different types of fishing gear and primers according to the work that we want to realize, which is why we must choose the correct path to achieve an optimal result. In Audioledcar you will find quantity of products to choose from for you to select the one that best suits your work needs. Inside each product you will be able to find all the information. If you have any doubt, you will only have to contact us and we will help you to choose the right one.